Saturday, April 27, 2013

Component Tester

The last project that i built it is a component tester, which is based on AVR-Transistortester by Mark Frejek. 
And here is the modified version further developed by Karl-Heinz Kübbeler.
You'll find all firmwares and  documentation  at http://www.mikrocontroller.net/svnbrowser/transistortester/.

 Here is the schematic:
 The PCB layout:

 And here is the final result:

Here is a list of the parts used in this project:

PartValue
PackageDescription



C1100nF
C025_050-025X075CAPACITOR
C21nF
C2.5-2CAPACITOR
C310nF
C2.5-2CAPACITOR
C422pF
C2.5-2CAPACITOR
C522pF
C2.5-2CAPACITOR
C6100nF
C025_050-025X075CAPACITOR
C7100nF
C025_050-025X075CAPACITOR
C8100nF
C025_050-025X075CAPACITOR
C9100uF
E5-10,5POLARIZED_CAPACITOR
C1010uF
E2,5-6EPOLARIZED_CAPACITOR
D11N4148
DO35-7DIODE
D2SCHOTTKY
DO35-7Schottky Diode
D3SCHOTTKY
DO35-7Schottky Diode
D41N4148
DO35-7DIODE
DIS1TUXGR_16X2_R2
TUXGR_16X2_R2Tuxgraphics LCD display 16x2 characters reflective, with background light

IC1ATmega8/168/328
DIL28-3MICROCONTROLLER
IC3LM7805
78XXLVOLTAGE REGULATOR
ISPISP
ML6HARTING

J1POWER_JACKPTHPOWER_JACK_PTHPower Jack
JP1+9V
1X01PIN HEADER
JP2GND
1X01PIN HEADER
L110µH
0207/10INDUCTOR
L210µH
0207/10INDUCTOR
LED1green
LED5MMLED
Q1BC557C
TO92-EBCPNP Transistror
Q2BC547B
TO92NPN Transistor
Q3BC547B
TO92NPN Transistor
Q48,000 MHz
HC49/SCRYSTAL

R110K
0207/10RESISTOR
R210K
0207/10RESISTOR
R33K3
0207/10RESISTOR
R43K3
0207/10RESISTOR
R52K7
0207/10RESISTOR
R627K
0207/10RESISTOR
R7100K
0207/10RESISTOR
R8680R
0207/10RESISTOR
R9470K
0207/10RESISTOR
R10680R
0207/10RESISTOR
R11470K
0207/10RESISTOR
R12680R
0207/10RESISTOR
R13470K
0207/10RESISTOR
R1410k
PT-10SPotentiometer
R1533-270
0207/10RESISTOR
R1633K
0207/10RESISTOR
R172K7
0207/10RESISTOR
R1847k
0207/10RESISTOR
S1Start Test
B3F-10XXOMRON SWITCH


SV2TEST PINS
FE05-2FEMALE HEADER

SV3TEST
MA03-1PIN HEADER

VREF1LM336 / LM4040
TO92-VREFVOLTAGE REFERENCE
   

Software Version 1.07k Specifications:


Measurment Range: 
   -Resistor:0.5Ω - 50MΩ.   
   -Capacitor:25pF - 100000uF.
   -Inductance:0.01mH - 20H.
 Features:
  -Operates with ATmega8, ATmega168 or ATmega328 microcontrollers.
  -Automatic detection of NPN and PNP transistors, N-channel and P-channel MOSFET, diode (including dual diode),Thyristor,Transistors, resistors and capacitors.
  -Automatic detection of pin layout of the detected part.
  -Measuring of current amplifcation factor and Base-Emitter threshold voltage of bipolar transistors.
  -Detection of the protection diode of bipolar transistors and MOSFETs.
  -Measuring of the Gate threshold voltage and Gate capacity value of MOSFETs.
  -Resolution of resistor measurement is now up to 0:01 values up to 50M are detected.
  -For resistors below 2100 also the measurement of inductance will be done,
  -Capacitors with values from 25pF to 100mF. The resolution can be up to 1 pF .
  -For capacitors with a capacity value above 0:18 F the Equivalent Serial Resistance (ESR) is
measured with a resolution of 0:01Ω.
  -For capacitors with a capacity value above 5000pF the voltage loss after a load pulse can be
determined. The voltage loss give a hint for the quality factor of the capacitor.
  -Zener-Diodes can be detected, if reverse break down Voltage is below 4.5V. 
  -LED is detected as diode, the flux voltage is much higher than normal.
  -Selectable facility to calibrate the internal port resistance of port output and the zero of set
of capacity measurement with the selftest.
  -Display battery voltage

   Edit:
Component Tester schematic Eagle
Component Tester board Eagle
Component Tester bottom pdf
Component Tester top pdf
Component Tester top silkscreen pdf
Component Tester box silkscreen psd

 Software
Posted by at 75 comments :
Labels: , , ,

Friday, April 12, 2013

Arduino and my clones


Arduino Uno. 


I started out with the very popular Arduino Uno board, which is based on Atmel AVR® Atmega328p 8-Bit Microcontroller. It's pretty easy to get started with Arduino, just get one of the boards, download the IDE, and start learning to program.

Arduino Single-Sided Serial Board (version 3).

This is the first Arduino clone that I built it.





westfw posted on Instructables this board, that I built it with female header.



MinimalDuino 107.


  posted on his blog an Arduino clone called Minimalduino, designed to match the form factor of the "official" Arduino boards.


FASTDUINO 32MHZ.

My successful attempt to run atmega328 at 32MHz 




all my boards


Posted by at 1 comment :
Labels: , , , , , , ,

Tuesday, April 9, 2013

Welcome


Hello everyone! I created this blog to share my ideas, projects and interest with you.
This is my way of giving back to the community from which I have learnt a lot.
I hope that you will find in it something useful. If you enjoy what's here, do come back for more updates.
Please leave a comment if you have any questions or feedback!
Posted by at 1 comment :
Labels:
Subscribe to: Comments ( Atom )